Change Language :
iglidur® G V0 is the first iglidur® material with a UL94 V0 rating for universal use in the normal temperature range. All other iglidur® materials with V0 rating are part of the high-temperature segment. The general mechanical and thermal specifications are largely comparable with the all-rounder iglidur® G.
| Descriptive technical specifications | |
|---|---|
Material data table
General properties
Unit
iglidur® G V0
Testing method
Density
g/cm³
1.53
Colour
black
Max. moisture absorption at +23°C/50% room humidity
% weight
0.7
DIN 53495
Max. moisture absorption
% weight
4.0
Coefficient of sliding friction, dynamic against steel
渭
0.07-0.20
pv value, max. (dry)
MPa x m/s
0.5
Mechanical properties
Flexural modulus
MPa
7,900
DIN 53457
Flexural strength at 20°C
MPa
140
DIN 53452
Compressive strength
MPa
100
Maximum recommended surface pressure (20°C)
MPa
75
Shore D hardness
80
DIN 53505
Physical and thermal properties
Max. long-term application temperature
°C
+130
Max. short-term application temperature
°C
+210
Min. application temperature
°C
-40
Thermal conductivity
W/m x K
0.25
ASTM C 177
Coefficient of thermal expansion (at 23°C)
K-1 x 10-5
9
DIN 53752
Electrical properties
Specific transitional resistance
Ωcm
< 1012
DIN IEC 93
Surface resistance
惟
< 1011
DIN 53482
Table 01: Material data

Diagram 01: Permissible pv values for iglidur® G V0 plain bearings with a wall thickness of 1mm in dry operation against a steel shaft at +20°C, mounted in a steel housing
X = Surface speed [m/s]
Y = Load [MPa]
When temperatures increase, the compressive strength of iglidur® G V0 plain bearings decreases. Diagram 02 shows this inverse relationship. With the long-term permitted application temperature of +130°C, the permitted surface pressure still amounts to 35MPa. The maximum recommended surface pressure is a mechanical material parameter. No conclusions regarding the tribological properties can be drawn from this. Diagram 03 shows the elastic deformation of iglidur® G V0 at radial loads. The plastic deformation is minimal up to a pressure of approximately 100MPa. However, it is also dependent on the service time.
iglidur® G V0 has been developed for low to medium surface speeds. The maximum values shown in table 03 can only be achieved at low pressures. In practice, though, this level is rarely reached due to varying application conditions.
Surface speeds of various iglidur materials
| Maximum surface speeds [m/s] | Rotating | Oscillating | Linear |
|---|---|---|---|
| Long-term | 1.0 | 0.7 | 4.0 |
| Short-term | 2.0 | 1.4 | 5.0 |
The ambient temperatures strongly influence the properties of plain bearings. The short-term maximum temperature permitted is +210°C and allows the use of iglidur® G V0 plain bearings in applications where the bearings are not subjected to any additional load, e.g. a paint drying process. The temperatures prevailing in the bearing system also have an influence on the wear. With increasing temperatures, the wear increases and this effect is significant when temperatures rise over +120°C. For temperatures over +100°C an additional securing is required.
Temperatures, coefficient of thermal expansion
| Min. application temperature | Upper application temperature, long-term | Upper application temperature, short-term | In addition secure axially from |
|---|---|---|---|
| -40°C | +130°C | +210°C | +100°C |
Similar to wear resistance, the coefficient of friction μ also changes with the load. The coefficient of friction decreases considerably with increasing loads, whereas a slight increase in surface speed causes an increase of the coefficient of friction. This relationship explains the excellent results of iglidur® G V0 plain bearings for high loads and low speeds (diagrams 04 and 05).
Coefficient of friction against steel (Ra = 1µm, 50HRC):
| iglidur G V0 | dry | Greases | Oil | Water |
|---|---|---|---|---|
| Coefficient of friction μ | 0.07-0.20 | 0.09 | 0.04 | 0.04 |
The friction and wear are also dependent, to a large degree, on the mating partner. Shafts that are too smooth increase both the coefficient of friction and the wear of the bearing. For iglidur® G V0 a ground surface with an average surface finish Ra = 0.6-0.8µm is recommended. Diagram 06 shows results of testing different shaft materials with plain bearings made from iglidur® G V0. It is important to notice that with increasing loads, the recommended hardness of the shaft increases. The "soft" shafts tend to wear themselves and thus increase the wear of the overall system. If the loads exceed 2MPa it is important to recognise that the wear rate (the gradient of the curves) clearly decreases with the hard shaft materials. The comparison of rotation and pivoting shows that iglidur® G V0 provides advantages in pivoting movements (diagram 07). If the shaft material you plan on using is not shown in these test results, please contact us.
iglidur® G V0 plain bearings have good chemical resistance at room temperature. They are resistant to most lubricants. iglidur® G V0 is not affected by most weak organic and inorganic acids.
All data at room temperature [+20 °C], + resistant 0 conditionally resistant - non-resistant
| Chemicals | Resistance |
|---|---|
| Alcohols | + up to 0 |
| Greases, oils without additives | + |
| Hydrocarbons | + |
| Fuels | + |
| Strong alkalines | 0 |
| Strong acids | - |
| Diluted alkalines | + |
| Diluted acids | 0 to - |
iglidur® G V0 plain bearings are standard bearings for shafts with h-tolerance (recommended minimum h9). The bearings are designed for press-fit into a housing machined to a H7 tolerance. After being assembled into a nominal size housing, the inner diameter automatically adjusts to the E10 tolerances.
Important tolerances according to ISO 3547-1 after press-fit:
| Diameter d1 [mm] | Housing H7 [mm] | iglidur G V0 plain bearing E10 [mm] | Shaft h9 [mm] |
|---|---|---|---|
| up to 3 | +0.000 +0.010 | +0.014 +0.054 | -0.025 +0.000 |
| > 3 up to 6 | +0.000 +0.012 | +0.020 +0.068 | -0.030 +0.000 |
| > 6 up to 10 | +0.000 +0.015 | +0.025 +0.083 | -0.036 +0.000 |
| > 10 up to 18 | +0.000 +0.018 | +0.032 +0.102 | -0.043 +0.000 |
| > 18 up to 30 | +0.000 +0.021 | +0.040 +0.124 | -0.052 +0.000 |
| > 30 up to 50 | +0.000 +0.025 | +0.050 +0.150 | -0.062 +0.000 |
| >50 to 80 | +0.000 +0.030 | +0.060 +0.180 | -0.074 +0.000 |
| >80 to 120 | +0.000 +0.035 | +0.072 +0.212 | -0.087 +0.000 |
| > 120 up to 180 | +0.000 +0.040 | +0.085 +0.245 | -0.100 +0.000 |
In person:
Monday to Friday from 7 am - 8 pm.
Saturdays from 8 am- 12 pm.
Online:
24h
WhatsApp-Service:
Montag – Freitag: 8 – 16 Uhr